DECLARATORIA de vigencia de la Norma Mexicana NMX-I-60793-2-10-NYCE-2021.

Al margen un sello con el Escudo Nacional, que dice: Estados Unidos Mexicanos.- ECONOMÍA.- Secretaría de Economía.- Unidad de Normatividad, Competitividad y Competencia.- Dirección General de Normas.

DECLARATORIA DE VIGENCIA DE LA NORMA MEXICANA NMX-I-60793-2-10-NYCE-2021, TELECOMUNICACIONES-FIBRAS Y CABLES-FIBRAS ÓPTICAS-CARACTERÍSTICAS DE FIBRAS MULTIMODO CATEGORÍA A1.
La Secretaría de Economía, por conducto de la Dirección General de Normas, con fundamento en lo dispuesto por los artículos 34 fracciones II, XIII y XXXIII de la Ley Orgánica de la Administración Pública Federal; 3 fracción X, 39 fracciones III y XII, 51-A, 54 y 66 fracción V de la Ley Federal sobre Metrología y Normalización, 45 y 46 del Reglamento de la Ley Federal sobre Metrología y Normalización; Tercero y Cuarto Transitorios del Decreto por el que se expide la Ley de Infraestructura de la Calidad y se abroga la Ley Federal sobre Metrología y Normalización; y 36 fracciones I, IX y XII del Reglamento Interior de la Secretaría de Economía, publica la Declaratoria de Vigencia de la Norma Mexicana que se enuncia a continuación, misma que ha sido elaborada, aprobada y publicada como Proyecto de Norma Mexicana bajo la responsabilidad del Organismo Nacional de Normalización denominado "Normalización y Certificación NYCE, S.C.", a través del Comité Técnico de Normalización Nacional de Electrónica y Tecnologías de la Información y Comunicación (COTENNETIC) de NYCE, lo que se hace del conocimiento de los productores, distribuidores, consumidores y del público en general.
El texto completo del documento puede ser consultado gratuitamente en la Dirección General de Normas de esta Secretaría, ubicada en Calle Pachuca número 189, Piso 7, Colonia Condesa, Demarcación Territorial Cuauhtémoc, Código Postal 06140, Ciudad de México, a través de una cita gestionada al correo electrónico consultapublica@economia.gob.mx o puede ser adquirido en la sede de dicho organismo, ubicado en Avenida Lomas de Sotelo número 1097, Colonia Lomas de Sotelo, Demarcación Territorial Miguel Hidalgo, Código Postal 11200, Ciudad de México, teléfono 55 5395-0777, Fax 55 5395-0700 y/o al correo electrónico: davila@nyce.org.mx.
La Norma Mexicana NMX-I-60793-2-10-NYCE-2021, entrará en vigor 60 días naturales contados a partir del día natural inmediato siguiente de la publicación de esta Declaratoria de Vigencia en el Diario Oficial de la Federación. SINEC-0210527165900983.
CLAVE O CÓDIGO
TÍTULO DE LA NORMA MEXICANA
NMX-I-60793-2-10-NYCE-2021
TELECOMUNICACIONES-FIBRAS Y CABLES-FIBRAS ÓPTICAS-CARACTERÍSTICAS DE FIBRAS MULTIMODO CATEGORÍA A1
Objetivo y campo de aplicación
La presente Norma Mexicana tiene por objeto establecer los tipos de fibra óptica multimodo para uso en cables de telecomunicaciones y las características de cada uno. Esta Norma Mexicana se aplica a las categorías de fibra óptica A1-OM1, AI-OM2, A1-OM3, A1-OM4 y A1-OM5. Estas fibras se usan o pueden ser incorporadas a cables o equipos para transmisión de información.
Concordancia con Normas Internacionales
Esta Norma Mexicana NMX-I-60793-2-10-NYCE-2021, Telecomunicaciones-Fibras y cables-Fibras ópticas-Características de fibras multimodo categoría A1, tiene concordancia MODIFICADA con la Norma Internacional IEC 60793-2-10:2019 Optical fibres-Part 2-10: Product specification-Sectional specification for category A1 multimode fibers y difiere en los siguientes puntos.
Capítulo/Inciso al que
aplica la diferencia
Desviación técnica / Justificación
Capítulo 1-Objetivo y
campo de aplicación
Especificaciones y los apéndices de esta Norma Mexicana concuerdan completamente con la Norma Internacional IEC-60793-2-10:2019
Capítulo 3-Definiciones y
términos abreviados
Se incluyeron definiciones y abreviaturas de uso en esta Norma Mexicana.
Capítulo 4-Clasificación
de fibras ópticas
multimodo
Se ha incluido la clasificación de las fibras ópticas especificadas
 
 
 
 
 
Bibliografía
-     IEC 60793-2-10-2017 Optical fibres-Part 2-10: Product specifications-Sectional specification for category A1 multimode fibres.
-     IEC 60793-1-20:2014 Optical fibres-Part 1-20: Measurement methods and test procedures-Fibre geometry.
-     IEC 60793-1-21:2001 Optical fibres-Part 1-21: Measurement methods and test procedures-Coating geometry.
-     IEC 60793-1-22:2001 Optical fibres-Part 1-22: Measurement methods and test procedures-Length measurement.
-     IEC 62048:2014 Optical fibres-Reliability-Power law theory.
-     IEC 60793-1-49:2018 Optical fibres-Part 1-49: Measurement methods and test procedures-Differential mode delay.
-     IEC 60794-1-1:2015 Optical fibre cables-Part 1-1: Generic specification-General.
-     IEC 60793-2:2019 Optical fibres-Part 2: Product specifications-General.
-     IEC 60793-1-50:2014 Optical fibres-Part 1-50: Measurement methods and test procedures-Damp heat (steady state) tests).
-      IEC 60793-1-51:2014 Optical fibres-Part 1-51: Measurement methods and test procedures-Dry heat (steady state) tests.
-      IEC 60793-1-52:2014 Optical fibres-Part 1-52: Measurement methods and test procedures-Change of temperature tests.
-      IEC 60793-1-53:2014 Optical fibres-Part 1-53: Measurement methods and test procedures-Water immersion tests.
-      IEC 60793-1-32:2018 Optical fibres-Part 1-32: Measurement methods and test procedures-Coating strippability.
-      IEC 60793-1-31:2019 Optical fibres-Part 1-31: Measurement methods and test procedures-Tensile strength.
 
-      IEC 60793-1-33:2017 Optical fibres-Part 1-33: Measurement methods and test procedures-Stress corrosion susceptibility.
-      IEC 60793-1-30:2010 Optical fibres-Part 1-30: Measurement methods and test procedures-Fibre proof test.
-      IEC 61280-4-1:2019 Fibre-optic communication subsystem test procedures-Part 4-1: Installed cabling plant-Multimode attenuation measurement.
-      IEC 61280-1-4:2009 Fibre optic communication subsystem test procedures-Part 1-4: General communication subsystems-Light source encircled flux measurement method.
-      IEC 61280-1-3:2010 Fibre optic communication subsystem test procedures-Part 1-3: General communication subsystems-Central wavelength and spectral width measurement.
-      ISO/IEC/IEEE 8802-3:2017 Information technology-Telecommunications and information exchange between systems-Local and metropolitan area networks-Specific requirements-Part 3: Standard for Ethernet.
-      ISO/IEC 14165-115:2006 Information technology-Fibre Channel-Part 115: Physical Interfaces (FC-PI).
-      ANSI/INCITS 479:2016 Information Technology-Fibre Channel-Physical Interface-5 (FC-PI-5).
-      ISO/IEC 14165-116:2005 Information technology-Fibre Channel-Part 116: 10 Gigabit (10GFC).
-      ANSI/INCITS 512:2015 Information Technology-Fibre Channel-Physical Interface-6 (FC-PI-6).
-      ISO/IEC 11801:2002 Information technology-Generic cabling for customer premises.
-      ISO/IEC 11801-1:2017 Information technology-Generic cabling for customer premises-Part 1: General requirements.
-      H. Murata, Handbook of Optical Fibers and Cables, 2nd Edition. New York: Marcel Dekker Inc., 1996, Figure 22.
-      J. Abbott, S. Bickham, P. Dainese, M. Li, "Fibers for Short-Distance Applications", Chapter 7 in Optical Fiber Telecommunications VIA. New York: Elsevier, 2013, Figure 7.3.
-      J. Ritger, J. Abbott, "New Delay Set for TIA Modelling", White paper, June 1, 2001.
-      J. Ritger, J. Abbott, "Fiber Delays for 10 Gb Risk Assessment", Presentation to FO2.2.1, June 25, 2001.
-      P. Kolesar, "Source Characteristics Development", Presentation to FO2.2.1, June 2001.
-      S. Golowich, J. Ritger, P. Kolesar, "Simulation of 50 µm 10 Gb Links", Presentation to FO2.2.1, June 25, 2001.
-      S. Golowich, P. Kolesar, J. Ritger, G. Giaretta, "Modelling, Simulation, and Experimental Study of a 50µm Multimode Fiber Serial 10 Gb Link", Presentation to IEEE 802.3ae, May, 2000 [viewed 2019-01-30].
-      J. Ritger, "Risk Analysis: EF limits and Wavelength Dependence", Presentation to FO2.2.1, June 25, 2001.
-      S. Golowich, P. Kolesar, J. Ritger, P. Pepeljugoski, "Modelling and Simulations for 10 Gb Multimode Optical Fiber Link Component Specifications", OFC 2001, paper WDD57.
 
-      P. Pepeljugoski, S. Golowich, "Measurements and simulations of intersymbol interference penalty in new high speed 50 µm multimode fiber links operating at 10 Gb/s", OFC 2001, paper WDD40.
-      J. Ritger, "Use of Differential Mode Delay in Qualifying Multi-Mode Optical Fiber for 10 Gbps Operation", OFMC 2001.
-      M. Hackert, " ITA FO-2.2.1 March 12, 2001 Update", March 2001 IEEE Plenary [viewed 2019-01-30].
-      P. Pepeljugoski, M. Hackert, J. Abbott, S. Swanson, S. Golowich, J. Ritger, P. Kolesar, C. Chen and P. Pleunis, "Development of System Specification for Laser Optimized 50 µm Multimode Fiber for Multi-gigabit Short Wavelength LANs", J. Lightwave Tech., volume 21, No. 5, p. 1256-1275, May 2003.
-      P. Pepeljugoski, S. Golowich, J. Ritger, P. Kolesar, A. Risteski, " Modeling and Simulation of Next-Generation Multimode Fiber Links", J. Lightwave Tech. Vol. 21, No. 5, p. 1242-1255, May 2003.
-      D. Cunningham and W. Lane, Gigabit Ethernet Networking. New York: Macmillan Technical Publishing, 1999 (Chapter 9-The Gigabit Ethernet Optical Link Model).
-      IEEE 100G-SR4 Example MMF Link Model.xls, Petrilla [viewed 2019-01-30].
-      32G Fibre Channel Model T11-12-376v0, Cunningham 9/27/2012 [viewed 2017- 07-04 2019-02-25].
-      IEEE P802.3ae 10Gb/s Ethernet Task Force Link Budget Spreadsheet (Version 3.1.16a) [viewed 2017-07-04 2019-01-30].
-      C. Caspar, R. Freund, F. Achten, A. Gholami, G. Kuyt ,P. Matthijsse and D. Molin "Impact of Transceiver Characteristics on the Performance of 10 GbE Links Applying OM-4 Multimode Fibers", Proceedings of the 57th IWCS Conference, p. 295-303, November 2008 A. Sengupta, "Simulation of 10GbE Multimode Optical Communications Systems", Proceedings of the 57th IWCS Conference, p. 320-326, November 2008.
-      G. Oulundsen III, Y. Sun, D. Vaidya, R. Lingle, Jr., T. Irujo, D. Mazzarese, "Important Performance Characteristics of Enhanced OM3 Fiber for 10 Gb/s Operation", Proceedings of the 57th IWCS Conference, p327-334, November 2008.
-      IEEE Std 802.3TM-2015, IEEE Standard for Ethernet, Clause 52 for 10GBASE-S, Clause 86 for 40GBASE-SR4 and 100GBASE-SR10, Clause 95 for 100GBASESR4, Clause 112 for 25GBASE-SR 3.
-      ISO/IEC 14165-116:2005, Information technology-Fibre channel-Part 116: 10 Gigabit fibre channel (10GFC).
-      ANSI/INCITS 479-2011, Information Technology-Fibre Channel-Physical Interface-5 (FC-PI-5), for 400-SN (4GFC), 800-SN and 800-SA (8GFC), 1600- SN (16GFC) 4.
-      ANSI/INCITS 512-2015, Information Technology-Fibre Channel-Physical Interface-6 (FC-PI-6), for 3200-SN (32GFC).
-      OM3, OM4, OM5 Modal Bandwidth Over Wavelengths for WDM, IEEE 802.3 NGMMF Study Group, 01-2018 [viewed 2019-01-30].
-      R.G. Smith and S. D. Personick, Receiver design for optical communication systems. In Topics in Applies Physics, Vol. 39, Semiconductor Devices for Optical Communications, H. Kressel (ed.). Berlin: Springer-Verlag, 1982.
-      Gair D. Brown, Bandwidth and rise time calculations for digital multimode fiberoptic data links. JLT 10, no. 5, p. 675-678, 1992 May.
-      NMX-I-60050-731-NYCE-2010, Vocabulario electrotécnico-Parte 731-Comunicación por fibra óptica (Cancela a la NMX-I-101/17-NYCE-2003), cuya Declaratoria de Vigencia fue publicada en el Diario Oficial de la Federación el 24 de enero de 2011.
-      NMX-I-61931-NYCE-2010, Telecomunicaciones-Cables-Fibras Óptica-Terminología, cuya Declaratoria de Vigencia fue publicada en el Diario Oficial de la Federación el 24 de enero de 2011.
 
Atentamente,
Ciudad de México, a 24 de noviembre de 2021.- Director General de Normas y Secretario Ejecutivo de la Comisión Nacional de Infraestructura de la Calidad, Lic. Alfonso Guati Rojo Sánchez.- Rúbrica.