DECLARATORIA de vigencia de la Norma Mexicana NMX-I-11801-1-NYCE-2020.

Al margen un sello con el Escudo Nacional, que dice: Estados Unidos Mexicanos.- ECONOMÍA.- Secretaría de Economía.- Unidad de Normatividad, Competitividad y Competencia.- Dirección General de Normas.

DECLARATORIA DE VIGENCIA DE LA NORMA MEXICANA NMX-I-11801-1-NYCE-2020, TECNOLOGÍAS DE LA INFORMACIÓN-CABLEADO ESTRUCTURADO GENÉRICO-PARTE 1: REQUISITOS GENERALES.

La Secretaría de Economía, por conducto de la Dirección General de Normas, con fundamento en lo dispuesto por los artículos 34 fracciones II, XIII y XXXIII de la Ley Orgánica de la Administración Pública Federal; 3 fracción X, 39 fracciones III y XII, 51-A, 54 y 66 fracción V de la Ley Federal sobre Metrología y Normalización, 45 y 46 del Reglamento de la Ley Federal sobre Metrología y Normalización; Tercero y Cuarto Transitorios del Decreto por el que se expide la Ley de Infraestructura de la Calidad y se abroga la Ley Federal sobre Metrología y Normalización; y 36 fracciones I, IX y XII del Reglamento Interior de la Secretaría de Economía, publica la Declaratoria de Vigencia de la Norma Mexicana que se enuncia a continuación, misma que ha sido elaborada, aprobada y publicada como Proyecto de Norma Mexicana bajo la responsabilidad del Organismo Nacional de Normalización denominado "Normalización y Certificación NYCE, S.C.", a través del Comité Técnico de Normalización Nacional de Electrónica y Tecnologías de la Información y Comunicación (COTENNETIC) de NYCE, lo que se hace del conocimiento de los productores, distribuidores, consumidores y del público en general.

El texto completo del documento puede ser consultado gratuitamente en la Dirección General de Normas de esta Secretaría, ubicada en Calle Pachuca número 189, Piso 7, Colonia Condesa, Demarcación Territorial Cuauhtémoc, Código Postal 06140, Ciudad de México, a través de una cita gestionada al correo electrónico consultapublica@economia.gob.mx o puede ser adquirido en la sede de dicho organismo, ubicado en Avenida Lomas de Sotelo número 1097, Colonia Lomas de Sotelo, Demarcación Territorial Miguel Hidalgo, Código Postal 11200, Ciudad de México, teléfono 5395-0777, Fax 5395-0700 y/o al correo electrónico: davila@nyce.org.mx.

La Norma Mexicana NMX-I-11801-1-NYCE-2020, entrará en vigor 60 días naturales contados a partir del día natural inmediato siguiente de la publicación de esta Declaratoria de Vigencia en el Diario Oficial de la Federación. SINEC20191114180321032.

CLAVE O CÓDIGO	TÍTULO DE LA NORMA MEXICANA
NMX-I-11801-1-NYCE-2020	TECNOLOGÍAS DE LA INFORMACIÓN-CABLEADO ESTRUCTURADO GENÉRICO-PARTE 1: REQUISITOS GENERALES.

Objetivo y campo de aplicación

Esta Norma Mexicana especifica los requisitos que son comunes a las normas de cableado para tecnologías de la información en edificaciones e infraestructura de uso comercial, residencial, industrial, salud, para centros de datos, entre otros. El cableado para tecnologías de la información especificado en esta Norma Mexicana es compatible con una amplia gama de servicios, entre los que se incluyen voz, datos y vídeo, que también pueden incorporar la alimentación de energía.

Esta Norma Mexicana especifica:

a) La estructura fundamental y la configuración de los requisitos genéricos de cableado dentro de los tipos de instalaciones definidos en otras normas o documentos técnicos;

b) Los requisitos de desempeño ambiental y de transmisión de canal;

c) Los requisitos de desempeño de enlace;

d) Implementaciones de referencia de cableado vertebral;

e) Los requisitos de operación de los componentes, haciendo referencia a las normas aplicables disponibles para componentes y métodos de prueba, cuando proceda; y

f) Los procedimientos de prueba para verificar la conformidad con los requisitos de desempeño de transmisión de cableado de las normas aplicables.

NOTA: Esta Norma Mexicana no contiene requisitos específicos de conformidad. Los documentos de diseño de cableado estructurado genérico incorporan los requisitos de esta Norma Mexicana como parte de sus requisitos de conformidad individuales.

Adicionalmente, esta Norma Mexicana proporciona información sobre las aplicaciones soportadas por los canales de cableado.

Concordancia con Normas Internacionales

Esta Norma Mexicana es idéntica (IDT) con la Norma Internacional ISO/IEC 11801-1:2017 Information technology-Generic cabling for customer premises-Part 1: General requirements.

Bibliografía

· CISPR 32:2015, Electromagnetic compatibility of multimedia equipment-Emission requirements.

· CISPR 35:2016, Electromagnetic compatibility of multimedia equipment-Immunity requirements.

· IEC 60027:2010 (all parts), Letter symbols to be used in electrical technology-Part 7: Power generation, transmission and distribution.

· IEC 60603-7-7:2010, Connectors for electronic equipment-Part 7-7: Detail specification for 8-way, shielded, free and fixed connectors for data transmission with frequencies up to 600 MHz.

· IEC 60068-2-14:2009, Environmental testing-Part 2-14: Tests-Test N: Change of temperature.

· IEC 60068-2-38:2009, Environmental testing-Part 2-38: Tests-Test Z/AD: Composite temperature/humidity cyclic test.

· IEC 60227-2:1997, Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V-Part 2: Test methods.

· IEC 60332-3:1992 (all parts), Tests on electric cables under fire conditions-Part 3: Tests on bunched wires or cables.

· IEC 60364-1:2005, Low-voltage electrical installations-Part 1: Fundamental principles, assessment of general characteristics, definitions.

· IEC 60512 (all parts), Connectors for electronic equipment-Tests and measurements.

· IEC 60603-7-71:2010, Connectors for electronic equipment-Part 7-71: Detail specification for 8-way, shielded, free and fixed connectors, for data transmission with frequencies up to 1 000 MHz.

· IEC 60512-1-1:2002, Connectors for electronic equipment-Tests and measurements-Part 1-1: General examination-Test 1a: Visual examination.

· IEC 60512-1-2:2002, Connectors for electronic equipment-Tests and measurements-Part 1-2: General examination-Test 1b: Examination of dimension and mass.

· IEC 60512-2-5:2003, Connectors for electronic equipment-Tests and measurements-Part 2-5: Electrical continuity and contact resistance tests-Test 2e: Contact disturbance.

· IEC 60512-13-1:2006, Connectors for electronic equipment-Tests and measurements-Part 13-1: Mechanical operation tests-Test 13a: Engaging and separating forces.

· IEC 60512-15-6:2008, Connectors for electronic equipment-Tests and measurements-Part 15-6: Connector tests (mechanical)-Test 15f: Effectiveness of connector coupling devices.

· IEC 60512-15-8:1998, Electromechanical components for electronic equipment-Basic testing procedures and measuring methods-Part 15: Mechanical tests on contacts and terminations Section 8: Test 15h-Contact retention system resistance to tool application.

· IEC 60512-25-3:2001, Connectors for electronic equipment-Tests and measurements-Part 25-3: Test 25c-Rise time degradation.

· IEC 60793-1-4X (all parts), Optical fibres-Part 1-4X: Measurement methods and test procedures.

· IEC 60793-2:2015, Optical fibres-Part 2: Product specifications-General

· IEC 61076-3-110:2016, Connectors for electronic equipment-Product requirements-Part 3-110: Detail specification for free and fixed connectors for data transmission with frequencies up to 3 000 MHz.

· IEC 60794-1-1:2015, Optical fibre cables-Part 1-1: Generic specification General.

· IEC 60794-1-2:2017, Optical fibre cables-Part 1-2: Generic specification-Basic optical cable test procedures-General guidance.

· IEC 60807-8:1992, Rectangular connectors for frequencies below 3 MHz-Part 8: Detail specification for connectors, four-signal contacts and earthing contacts for cable screen.

· IEC 60512-99-001:2012, Connectors for electronic equipment-Tests and measurements-Part 99-001: Test schedule for engaging and separating connectors under electrical load-Test 99a: Connectors used in twisted pair communication cabling with remote power.

· IEC 60825-2:2004, Safety of laser products-Part 2: Safety of optical fibre communication systems (OFCS).

· IEC 60874-1:2011, Fibre optic interconnecting devices and passive components-Connectors for optical fibres and cables-Part 1: Generic specification.

· IEC 61754-20-100:2012, Fibre optic interconnecting devices and passive components-Fibre optic connector interfaces-Part 20-100: Interface standard for LC connectors with protective housings related to IEC 61076-3-106.

· IEC 61000-2-2:2002, Electromagnetic compatibility (EMC)-Part 2-2: Environment-Compatibility levels for low-frequency conducted disturbances and signalling in public low-voltage power supply systems.

· IEC TR 61000-5-2:1997, Electromagnetic compatibility (EMC)-Part 5: Installation and mitigation guidelines-Section 2: Earthing and cabling.

· IEC 61073-1:2009, Fibre optic interconnecting devices and passive components-Mechanical splices and fusion splice protectors for optical fibres and cables-Part 1: Generic specification.

· IEC 61280 (all parts), Fibre optic communication subsystem test procedures.

· IEC 61280-4-1:2009, Fibre optic communication subsystem test procedures-Part 4-1: Installed cable plant-Multimode attenuation measurement.

· IEC 61280-4-2:2014, Fibre optic communication subsystem test procedures-Part 4-2: Installed cable plant-Single-mode attenuation and optical return loss measurement.

· IEC 61300 (all parts), Fibre optic interconnecting devices and passive components-Basic test and measurement procedures.

· IEC 61300-1:2016, Fibre optic interconnecting devices and passive components-Basic test and measurement procedures-Part 1: General and guidance.

· IEC 61300-2-2:2009, Fibre optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-2: Tests-Mating durability.

· IEC 61300-2-6:2010, Fibre optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-6: Tests-Tensile strength of coupling mechanism.

· IEC 61300-2-12:2009, Fibre optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-12: Tests-Impact.

· IEC 61300-2-17:2010, Fibre optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-17: Tests-Cold.

· IEC 61300-2-19:2012, Fibre optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-19: Tests-Damp heat (steady state).

· IEC 61300-2-42:2014, Fibre optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-42: Tests-Static side load for strain relief.

· IEC 61300-3-6:2008, Fibre optic interconnecting devices and passive components-Basic test and measurement procedures-Part 3-6: Examinations and measurements-Return loss.

· IEC 61300-3-34:2009, Fibre optic interconnecting devices and passive components-Basic test and measurement procedures-Part 3-34: Examinations and measurements-Attenuation of random mated connectors.

· IEC 61753-1-3:2014, Fibre optic interconnecting devices and passive components-Performance standard-Part 1-3: General and guidance for single-mode fibre optic connector and cable assembly for industrial environment, Category I.

· IEC 61754-7-1:2014, Fibre optic interconnecting devices and passive components-Fibre optic connector interfaces-Part 7-1: Type MPO connector family-One fibre row.

· IEC 61754-7-2, Fibre optic interconnecting devices and passive components-Fibre optic connector interfaces-Part 7-2: Type MPO connector family-Two fibre rows.

· IEC 61935-3:2008, Testing of balanced and coaxial information technology cabling-Part 3: Installed cabling as specified in ISO/IEC 15018 and related standards.

· IEC TR 62000:2010, Guidance for combining different single-mode fibres types.

· ISO/IEC 8877:1992, Information technology-Telecommunications and information Exchange between systems-Interface connector and contact assignments for ISDN Basic Access Interface located at reference points S and T.

· ISO/IEC 11801-2:2017, Information technology-Generic cabling for customer premises-Part 2: Office premises.

· ISO/IEC 11801-3:2017, Information technology-Generic cabling for customer premises-Part 3: Industrial premises.

· ISO/IEC 11801-4:2017, Information technology-Generic cabling for customer premises-Part 4: Single-tenant homes.

· ISO/IEC 11801-5:2017, Information technology-Generic cabling for customer premises-Part 5: Data centers.

· ISO/IEC 11801-6:2017, Information technology-Generic cabling for customer premises-Part 6: Distributed building services.

· ISO/IEC 14165-114:2005, Information technology-Fibre channel-Part 114: 100 MB/s balanced copper physical interface (FC-100-DF-EL-S).

· ISO/IEC 14709-1:1997, Information technology-Configuration of Customer Premises Cabling (CPC) for applications-Part 1: Integrated Services Digital Network (ISDN) basic access.

· ISO/IEC 14709-2:1998, Information technology-Configuration of Customer Premises Cabling (CPC) for applications-Part 2: Integrated Services Digital Network (ISDN) primary rate.

· ISO/IEC TR 29125:2017, Information technology-Telecommunications cabling requirements for remote powering of terminal equipment.

· ISO/IEC:2015, Information technology -- Telecommunications bonding networks for buildings and other structures.

· ISO/IEC 18598:2016, Information technology-Automated infrastructure management (AIM) systems-Requirements, data exchange and applications.

· ISO/IEC TR 24704:2004, Information technology-Customer premises cabling for wireless access points.

· ISO/IEC TR 24750:2007, Information technology-Assessment and mitigation of installed balanced cabling channels in order to support 10GBASE-T.

· ISO/IEC TR 29106:2007, Information technology-Generic cabling-Introduction to the MICE environmental classification.

· ISO/IEC TS 29125:2017, Information technology-Telecommunications cabling requirements for remote powering of terminal equipment.

· ISO/IEC/IEEE 8802-3:2017, Information technology-Telecommunications and information exchange between systems-Local and metropolitan area networks-Specific requirements Part 3: Standard for Ethernet.

· ITU-T Rec. I.430:1995, Basic user-network interface-Layer 1 specification.

· ITU-T Rec. I.431:1993, Primary rate user-network interface-Layer 1 specification.

· ITU-T Rec. X.21:1992, Interface between data terminal equipment (DTE) and data circuit terminating equipment (DCE) for synchronous operation on public data networks.

· IEEE 802.3:2018, Standard for Ethernet.

· IEEE 802.3bt:2018, Standard for Ethernet Amendment: Physical Layer and Management.

· Parameters for DTE Power via MDI over 4-Pair.

· ISO/IEC/IEEE 8802-3:2017/AMD3:2017, Amendment 3-Information technology-Telecommunications and information exchange between systems-Local and metropolitan area networks-Specific requirements-Part 3: Standard for Ethernet-Physical layers and management parameters for 25 Gb/s and 40 Gb/s operation, types 25GBASE-T and 40GBASE-T.

· ISO/IEC/IEEE/8802-3:2017/AMD7:2017, Amendment 7-Information technology-Telecommunications and information exchange between systems-Local and metropolitan area networks-Specific requirements-Part 3: Standard for Ethernet-Media access control parameters, physical layers, and management parameters for 2.5 Gb/s and 5 Gb/s operation, types 2.5GBASE-T and 5GBASE-T.

· IEEE 1394b:2006, IEEE Standard for Higher-Performance Serial Bus.

· ISO/IEC 11801 (all parts), Information technology-Generic cabling for customer premises.

· ISO/IEC TR 11801-99 (all parts), Information technology-Generic cabling systems for customer premises.

· IEC 60352 (all parts), Solderless connections.

· IEC 61156-4:2009, Multicore and symmetrical pair/quad cables for digital communications-Part 4: Riser cables-Sectional specification.

· IEC 60352-8:2016, Radio frequency and coaxial cable assemblies-Part 2-6: Detail specification for cable assemblies for radio and TV receivers-Frequency range 0 MHz to 3 000 MHz, IEC 61169-24 connectors.

· IEC 61156-6:2010, Multicore and symmetrical pair/quad cables for digital communications-Part 6: Symmetrical pair/quad cables with transmission characteristics up to 1 000 MHz-Work area wiring-Sectional specification.

· IEC 61156-7:2003, Multicore and symmetrical pair/quad cables for digital communications-Part 7: Symmetrical pair cables with transmission characteristics up to 1 200 MHz-Sectional specification for digital and analog communication cables.

· IEC 61156-9:2016, Multicore and symmetrical pair/quad cables for digital communications-Part 9: Cables for channels with transmission characteristics up to 2 GHz-Sectional specification.

· IEC 61156-10:2016, Multicore and symmetrical pair/quad cables for digital communications-Part 10: Cables for cords with transmission characteristics up to 2 GHz-Sectional specification.

· IEC 61156-5-1:2009, Multicore and symmetrical pair/quad cables for digital communications-Part 5-1: Symmetrical pair/quad cables with transmission characteristics up to 1 000 MHz-Horizontal floor wiring-Blank detail specification.

· IEC 61156-6-1:2009, Multicore and symmetrical pair/quad cables for digital communications-Part 6-1: Symmetrical pair/quad cables with transmission characteristics up to 1 000 MHz-Work area wiring-Blank detail specification.

· IEC 61196-1:2005, Coaxial communication cables-Part 1: Generic specification-General, definitions and requirements.

· IEC 61156 (all parts), Multicore and symmetrical pair/quad cables for digital communications.

· IEC 61196-7:2011, Coaxial communication cables-Part 7: Sectional specification for cables for BCT cabling in accordance with ISO/IEC 15018-Indoor drop cables for systems operating at 5 MHz-3 000 MHz.

· IEC 60794-2:2017, Optical fibre cables-Part 2: Indoor cables-Sectional specification.

· IEC 60794-3:2014, Optical fibre cables-Part 3: Outdoor cables-Sectional specification.

· IEC 60794-5:2014, Optical fibre cables-Part 5: Sectional specification-Microduct cabling for installation by blowing.

· IEC 60794-1-21:2015, Optical fibre cables-Part 1-21: Generic specification-Basic optical cable test procedures-Mechanical tests methods.

· IEC 60794-1-22:2017, Optical fibre cables-Part 1-22: Generic specification-Basic optical cable test procedures-Environmental test methods.

· IEC 60794-2-51:2014, Optical fibre cables-Part 2-51: Indoor cables-Detail specification for simplex and duplex cables for use in cords for controlled environment.

· IEC 60793-2-50:2015, Optical fibres-Part 2-50: Product specifications-Sectional specification for class B single-mode fibres.

· IEC 60793-2-10:2017, Optical fibres-Part 2-10: Product specifications-Sectional specification for category A1 multimode fibres.

· IEC 61169-1:2013, Radio frequency connectors-Part 1: Generic specification-General requirements and measuring methods.

· IEC 61753 (all parts), Fibre optic interconnecting devices and passive components-Performance standard.

· IEC 60603-7(all parts), Connectors for electronic equipment.

· IEC 62664 (all parts), Fibre optic interconnecting devices and passive components-Fibre optic connector product specifications.

· IEC 61754 (all parts), Fibre optic interconnecting devices and passive components-Fibre optic connector interfaces.

· IEC 61753-022-2:2012, Fibre optic interconnecting devices and passive components-Performance standard-Part 022-2: Fibre optic connectors terminated on multimode fibre for category C-Controlled environment.

· IEC 61753-021-2:2007, Fibre optic interconnecting devices and passive components -Performance standard-Part 021-2: Grade C/3 single-mode fibre optic connectors for category C-Controlled environment.

· IEC 61753-021-3:2012, Fibre optic interconnecting devices and passive components-Performance standard-Part 021-3: Single-mode fibre optic connectors for category U-Uncontrolled environment.

· IEC 61076-3-106:2006, Connectors for electronic equipment-Product requirements-Part 3-106: Rectangular connectors-Detail specification for protective housings for use with 8-way shielded and unshielded connectors for industrial environments incorporating the IEC 60603-7 series interface.

· NMX-I-007/1-NYCE-2006, Equipos y componentes electrónicos-Métodos de pruebas ambientales y durabilidad-Parte 1: Generalidades y guía. Cuya Declaratoria de Vigencia fue publicada en el Diario el 3 de noviembre de 2006.

· IEC 61076-3-104:2017, Connectors for electrical and electronic equipment-Product requirements-Part 3-104: Detail specification for 8-way, shielded free and fixed connectors for data transmissions with frequencies up to 2 000 MHz.

· IEC 61076-2-101:2012, Connectors for electronic equipment-Product requirements-Part 2-101: Circular connectors-Detail specification for M12 connectors with screw-locking.

· IEC 61076-2-109:2014, Connectors for electronic equipment-Product requirements-Part 2-109: Circular connectors-Detail specification for connectors with M 12 x 1 screw-locking, for data transmission frequencies up to 500 MHz.

· IEC 61169-2:2007, Radio-frenquency connectors-Part 2: Sectional specification-Radio frequency coaxial connectors of type 9,52.

· IEC 61169-24:2009, Radio-frequency connectors-Part 24: Sectional specification-Radio frequency coaxial connectors with screw coupling, typically for use in 75 O cable networks (type F).

· IEC 61754-7-2:2017, Fibre optic interconnecting devices and passive components-Fibre optic connector interfaces-Part 7-2: Type MPO connector family-Two fibre rows.

· IEC 61935-2:2010, Specification for the testing of balanced and coaxial information technology cabling-Part 2: Cords as specified in ISO/IEC 11801 and related standards.

· IEC 60966-2-4:2016, Radio frequency and coaxial cable assemblies-Part 2-4: Detail specification for cable assemblies for radio and TV receivers-Frequency range 0 MHz to 3 000 MHz, IEC 61169-2 connectors.

· IEC 60966-2-5:2016, Radio frequency and coaxial cable assemblies-Part 2-5: Detail specification for

· IEC 60966-2-5:2016, Radio frequency and coaxial cable assemblies-Part 2-5: Detail specification for cable assemblies for radio and TV receivers-Frequency range 0 MHz to 1 000 MHz, IEC 61169-2 connectors.

· IEC 60966,2-6:2016, Radio frequency and coaxial cable assemblies-Part 2-6: Detail specification for cable assemblies for radio and TV receivers-Frequency range 0 MHz to 3 000 MHz, IEC 61169-24 connectors.

· IEC 61753-1:2018, Fibre optic interconnecting devices and passive components-Performance standard-Part 1: General and guidance.

· IEC 60603-7-1:2011, Connectors for electronic equipment-Part 7-1: Detail specification for 8-way, shielded, free and fixed connectors.

· IEC 60352-2:2006, Solderless connections-Part 2: Crimped connections-General requirements, test methods and practical guidance.

· IEC 60352-3:1993, Solderless connections-Part 3: Solderless accessible insulation displacement connections-General requirements, test methods and practical guidance.

· IEC 60352-4:1994, Solderless connections-Part 4: Solderless non-accessible insulation displacement connections-General requirements, test methods and practical guidance.

· IEC 60352-5:2012, Solderless connections-Part 5: Press-in connections-General requirements, test methods and practical guidance.

· IEC 60352-6:1997, Solderless connections-Part 6: Insulation piercing connections-General requirements, test methods and practical guidance.

· IEC 60352-7:2002, Solderless connections-Part 7: Spring clamp connections-General requirements, test methods and practical guidance.

· IEC 60708:2005, Low-frequency cables with polyolefin insulation and moisture barrier polyolefin sheath.

· IEC 60512-6-2:2002, Connectors for electronic equipment-Tests and measurements-Part 6-2: Dynamic stress tests-Test 6b: Bump.

· IEC 60512-6-3:2002, Connectors for electronic equipment-Tests and measurements-Part 6-3: Dynamic stress tests-Test 6c: Shock.

· IEC 60512-6-4:2002, Connectors for electronic equipment-Tests and measurements-Part 6-4: Dynamic stress tests-Test 6d: Vibration (sinusoidal).

· IEC 60512-16-4:2008, Connectors for electronic equipment-Tests and measurements-Part 16-4: Mechanical tests on contacts and terminations-Test 16d: Tensile strength (crimped connections).

· IEC 60512-17-4:2010, Connectors for electronic equipment-Tests and measurements-Part 17-4: Cable clamping tests-Test 17d: Cable clamp resistance to cable torsion.

· IEC 60529:1989, Degrees of protection provided by enclosures (IP Code).

· IEC 60512-11-9:2002, Connectors for electronic equipment-Tests and measurements-Part 11-9: Climatic tests-Test 11i: Dry heat.

· IEC 60512-11-10:2002, Connectors for electronic equipment-Tests and measurements-Part 11-10: Climatic tests-Test 11j: Cold.

· IEC 60512-11-4:2002, Connectors for electronic equipment-Tests and measurements-Part 11-4: Climatic tests-Test 11d: Rapid change of temperature.

· ISO 4892-1:2016, Plastics -Methods of exposure to laboratory light sources- Part 1: General guidance.

· ISO 4892-2:2013, Plastics -Methods of exposure to laboratory light sources-Part 2: Xenon-arc lamps.

· IEC 60512-11-12:2002, Connectors for electronic equipment-Tests and measurements-Part 11-12: Climatic tests-Test 11m: Damp heat, cyclic.

· IEC 60512-19-3:1997, Electromechanical components for electronic equipment-Basic testing procedures and measuring methods-Part 19: Chemical resistance tests-Section 3: Test 19c-Fluid resistance.

· IEC 60512-11-7:2003, Connectors for electronic equipment-Tests and measurements-Part 11-7: Climatic tests-Test 11g: Flowing mixed gas corrosion test.

· IEC 60512-23-3:2000, Electromechanical components for electronic equipment-Basic testing procedures and measuring methods-Part 23-3: Test 23c: Shielding effectiveness of connectors and accessories.

· IEC 60512-4-2:2002, Connectors for electronic equipment-Tests and measurements-Part 4-2: Voltage

· IEC 60512-4-2:2002, Connectors for electronic equipment-Tests and measurements-Part 4-2: Voltage stress tests-Test 4b: Partial discharge.

· IEC 60512-4-1:2003, Connectors for electronic equipment-Tests and measurements-Part 4-1: Voltage stress tests-Test 4a: Voltage proof.

· IEC 60966-1:1999, Radio frequency and coaxial cable assemblies-Part 1: Generic specification-General requirements and test methods.

· IEC 61300-2-9:2017, Fibre optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-9: Tests-Shock.

· IEC 61300-2-1:2009, Fibre optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-1: Tests-Vibration (sinusoidal).

· IEC 61300-2-4:1995, Fibre optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-4: Tests-Fibre/cable retention.

· IEC 61300-2-5:2009, Fibre optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-5: Tests-Torsion.

· IEC 61300-2-44:2013, Fibre optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-44: Tests-Flexing of the strain relief of fibre optic devices.

· IEC 61300-2-18:2005, Fibre optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-18: Tests-Dry heat-High temperature endurance.

· IEC 61300-2-22:2007, Fibre optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-22: Tests-Change of temperature.

· IEC 61300-2-46:2006, Fibre optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-46: Tests-Damp heat, cyclic.

· IEC 61300-2-34:2009, Fibre optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-34: Tests-Resistance to solvents and contaminating fluids of interconnecting components and closures.

· IEC 60603-7-2:2010, Connectors for electronic equipment-Part 7-2: Detail specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 100 MHz.

· IEC 60603-7-3:2010, Connectors for electronic equipment-Part 7-3: Detail specification for 8-way, shielded, free and fixed connectors, for data transmission with frequencies up to 100 MHz.

· IEC 60603-7-4:2010, Connectors for electronic equipment-Part 7-4: Detail specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 250 MHz.

· IEC 60603-7-5:2010, Connectors for electronic equipment-Part 7-5: Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 250 MHz.

· IEC 60603-7-41:2010, Connectors for electronic equipment-Part 7-41: Detail specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 500 MHz.

· IEC 60603-7-51:2010, Connectors for electronic equipment-Part 7-51: Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 500 MHz.

· IEC 60603-7-81:2015, Connectors for electronic equipment-Part 7-81: Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 2 000 MHz.

· IEC 60603-7-82:2016, Connectors for electronic equipment-Part 7-82: Detail specification for 8-way, 12 contacts, shielded, free and fixed connectors, for data transmission with frequencies up to 2 000 MHz.

· IEC 61918:2018, Industrial communication networks-Installation of communication networks in industrial premises.

· ISO/IEC TR 11801-9901:2014, Information technology-Generic cabling for customer premises-Part 9901: Guidance for balanced cabling in support of at least 40 Gbit/s data transmission.

· ISO/IEC TR 11801-9902:2017, Information technology-Generic cabling for customer premises-Part 99-2: End-to-end link configurations.

· ISO/IEC TR 11801-9903:2015, Information technology-Generic cabling systems for customer premises-Part 9903: Matrix modelling of channels and links.

· ISO/IEC TR 11801-9904:2017, Information technology-Generic cabling for customer premises-Part 9904: Assessment and mitigation of installed balanced cabling channels to support 2,5GBASE-T and 5GBASE-T.

· ISO/IEC TR 11801-9905:2018, Information technology-Generic cabling systems for customer premises-Part 9905: Guidelines for the use of installed cabling to support 25GBASE-T application.

· ISO/IEC 11801-1:2017, Information technology-Generic cabling for customer premisesPart 1: General requirements.

· NMX-J-364/4-41-ANCE-2014, Instalaciones eléctricas-Parte 4-41: Protección para seguridad-Protección contra choque eléctrico. Cuya Declaratoria de Vigencia fue publicada en el Diario Oficial de la Federación el 24 de septiembre de 2014.

· NMX-J364/4-44-ANCE-2013, Instalaciones eléctricas-Parte 4-44: Protección para la seguridad-Protección contra perturbaciones de tensión y perturbaciones electromagnéticas. Cuya Declaratoria de Vigencia fue publicada en el Diario Oficial de la Federación el 28 de octubre de 2013.

· NMX-I-60950-1-NYCE-2015, Equipo de tecnologías de la información-Seguridad-Requisitos generales. Cuya Declaratoria de Vigencia fue publicada en el Diario Oficial de la Federación el 13 de mayo de 2015.

· NMX-I-271/01-NYCE-2008, Electrónica-Seguridad de los productos laser-Parte 01: Clasificación de los equipos y requisitos. Cuya Declaratoria de Vigencia fue publicada en el Diario Oficial de la Federación el 19 de junio de 2008.

· NMX-I-213-NYCE-2009, Telecomunicaciones-Cables-Cable óptico-Dieléctrico para uso aéreo autosoportado (ODAS)-Especificaciones y métodos de prueba. Cuya Declaratoria de Vigencia fue publicada en el Diario Oficial de la Federación el 28 de enero de 2010.

· NMX-I-208/01-NYCE-2007, Electrónica-Conectores para equipos electrónicos-Pruebas y mediciones-Parte 01: Generalidades. Cuya Declaratoria de Vigencia fue publicada en el Diario Oficial de la Federación el 27 de noviembre de 2007.

· ISO/IEC 14165-115:2006 Information technology-Fibre Channel-Part 115: Physical Interfaces (FC-PI).

· IEC 60728-1 Cabled distribution systems for television and sound signals-Part 1: Methods of measurement and system performance.

· IEC 61784-5-1:2013 Industrial communication networks-Profiles-Part 5-1: Installation of fieldbuses-Installation profiles for CPF 1.

· IEC 61784-5-2:2018 Industrial communication networks-Profiles-Part 5-2: Installation of fieldbuses-Installation profiles for CPF 2.

· IEC 61784-5-3:2018 Industrial communication networks-Profiles-Part 5-3: Installation of fieldbuses-Installation profiles for CPF 3.

· IEC 61784-5-4:2010 Industrial communication networks-Profiles-Part 5-4: Installation of fieldbuses-Installation profiles for CPF 4.

· IEC 61784-5-6:2018 Industrial communication networks-Profiles-Part 5-6: Installation of fieldbuses-Installation profiles for CPF 6.

· IEC 61784-5-8:2018 Industrial communication networks-Profiles-Part 5-8: Installation of fieldbuses-Installation profiles for CPF 8.

· IEC 61784-5-10:2010 Industrial communication networks-Profiles-Part 5-10: Installation of fieldbuses-Installation profiles for CPF 10.

· IEC 61784-5-11:2013 Industrial communication networks-Profiles-Part 5-11: Installation of fieldbuses-Installation profiles for CPF 11.

· IEC 61784-5-12:2018 Industrial communication networks-Profiles-Part 5-12: Installation of fieldbuses-Installation profiles for CPF 12.

· IEC 61784-5-13:2013 Industrial communication networks-Profiles-Part 5-13: installation of fieldbuses-Installation profiles for CPF 13.

· IEC 61784-5-14:2013 Industrial communication networks-Profiles-Part 5-14: Installation of fieldbuses-Installation profiles for CPF 14.

· IEC 61784-5-15:2010 Industrial communication networks-Profiles-Part 5-15: Installation of fieldbuses-Installation profiles for CPF 15.

· IEC 61784-5-16:2013 Industrial communication networks-Profiles-Part 5-16: Installation of fieldbuses-Installation profiles for CPF 16.

· IEC 61784-5-17:2013 Industrial communication networks-Profiles-Part 5-17: Installation of fieldbuses-Installation profiles for CPF 17.

· IEC 61784-5-18:2018 Industrial communication networks-Profiles-Part 5-18: Installation of fieldbuses-Installation profiles for CPF 18.

· IEC 61784-5-19:2013 Industrial communication networks-Profiles-Part 5-19: Installation of fieldbuses-Installation profiles for CPF 19.

Atentamente,

Ciudad de México, a 21 de julio de 2021.- Director General de Normas y Secretario Ejecutivo de la Comisión Nacional de Infraestructura de la Calidad, Lic. Alfonso Guati Rojo Sánchez.- Rúbrica.